Magazine Rack Design

DIY Magazine Rack Design: Wall-Mounted Wooden Organizer Plans and Building Guide

A wall-mounted wooden magazine rack is a practical woodworking project for organizing magazines, catalogs, brochures, and other reading materials. By keeping publications off tables and floors, a magazine organizer can help reduce clutter in a living room, home office, bedroom, or waiting area.

Building your own magazine rack allows you to choose the dimensions, wood species, finish, and number of storage compartments. A simple design can complement modern, rustic, or traditional furniture while making frequently used reading materials easier to reach.

The Pinterest woodworking blueprint above provides inspiration for a wall-mounted magazine rack with angled storage slots. This guide explains the design considerations and presents a separate example using a wooden back panel and three shallow magazine pockets.

Project note: The measurements below describe an original example project, not an exact reproduction of the Pinterest drawing. The example uses individual sloped-front pockets rather than cutting deep slots through a single board. This provides a straightforward alternative for beginners while retaining the angled-storage concept.

Why Build a Wall-Mounted Magazine Rack?

  • Save floor space: Wall-mounted storage is useful in smaller rooms.
  • Reduce clutter: Keep magazines and catalogs in one organized location.
  • Improve accessibility: Angled pockets make reading materials easier to see and retrieve.
  • Customize the appearance: Choose wood and finishes that match your decor.
  • Develop woodworking skills: Practice measuring, straight cuts, angled cuts, assembly, and finishing.
  • Create useful storage: Adapt the pockets for lightweight brochures, mail, or other suitable paper items.

Key Features of the Magazine Rack Design

Wall-Mounted Construction

The magazine rack attaches to suitable wall structure using properly selected mounting hardware.

Wall mounting keeps the organizer off the floor and helps preserve space around desks, sofas, and other furniture.

Angled Storage Pockets

Each pocket has a slightly sloped front panel that makes magazines easier to insert and remove.

The pockets should be deep enough to retain the magazines without hiding their entire covers.

Three Storage Levels

The example uses three vertically arranged pockets.

This layout provides separate spaces for magazines, catalogs, or other lightweight reading materials.

Simple Wooden Back Panel

A single back panel supports the pocket assemblies and provides a convenient surface for positioning mounting hardware.

Customizable Finish

The rack can be painted, stained, or finished with a clear protective coating.

Example Magazine Rack Dimensions

This example uses a compact vertical layout intended for wall mounting.

Feature Example measurement
Overall width 14 inches
Back panel height 36 inches
Back panel thickness 3/4 inch
Number of pockets 3
Pocket width 12 inches
Pocket front height Approximately 6 inches
Pocket projection Approximately 3 inches

The pocket projection and front-panel angle are approximate design targets. The final dimensions depend on the selected joinery and side-piece geometry.

Planning tip: Measure the magazines you intend to store before cutting. Large-format magazines and thick catalogs may require wider or deeper pockets.

Materials Needed for a Wooden Magazine Rack

  • 3/4-inch plywood or suitable solid wood for the back panel
  • 1/2-inch plywood or suitable wood for the pocket fronts and bottoms
  • 1/2-inch wood for the pocket side pieces
  • Wood glue
  • Suitable small wood screws or other appropriate joinery fasteners
  • Corrosion-resistant mounting screws where required
  • Wall-mounting hardware rated for the intended load and wall construction
  • Sandpaper
  • Optional wood filler
  • Optional paint, stain, or clear finish

Choose flat material with minimal warping. Plywood can be convenient for this project because it provides stable panels that are easy to cut to consistent dimensions.

Magazine Rack Cutting List

The following list provides starting dimensions for the three-pocket example.

The pocket side pieces are cut to their final shape after the desired front angle and pocket depth have been established.

Component Quantity Starting cut size
Back panel, 3/4-inch material 1 14 × 36 inches
Pocket front panels, 1/2-inch material 3 12 × 6 inches
Pocket bottom panels, 1/2-inch material 3 11 × 2 1/2 inches
Pocket side blanks, 1/2-inch material 6 Approximately 6 × 3 inches, shape to fit
Optional mounting cleat As required Size for selected mounting method

Assembly clarification: The pocket fronts are 12 inches wide, while the bottom panels fit between two 1/2-inch-thick side pieces. The 11-inch bottom length is a starting measurement for this arrangement.

The angled side profiles and their mating edges must be laid out and dry-fitted before final cutting. The front, bottom, and side pieces may require trimming depending on the chosen angle and joint arrangement.

This is an example cutting list rather than a dimensioned reproduction of the Pinterest blueprint.

Tools Required

  • Measuring tape
  • Pencil
  • Combination square
  • Protractor or adjustable angle gauge
  • Circular saw, table saw, or suitable hand saw
  • Jigsaw or another suitable tool for shaping side pieces
  • Drill and driver bits
  • Clamps
  • Orbital sander or sanding block
  • Stud finder or suitable wall-structure locating method
  • Level
  • Safety glasses, hearing protection, and dust protection

How to Build a Wall-Mounted Magazine Rack

Step 1: Measure Your Magazines

Measure the width, height, and thickness of the magazines or catalogs you plan to store.

Determine whether the 12-inch-wide pockets will provide enough space.

Allow clearance so publications can be inserted and removed without binding.

Step 2: Plan the Pocket Layout

Draw the 14 × 36-inch back panel.

Mark the proposed positions of the three magazine pockets.

Allow enough vertical spacing so the magazines in one pocket do not obstruct access to the pocket above.

Check the layout with actual magazines before cutting the pocket components.

Step 3: Cut the Back Panel

Cut the back panel to 14 × 36 inches.

Check that the corners are square.

Sand the cut edges to remove splinters.

Step 4: Cut the Pocket Front Panels

Cut three front panels measuring 12 × 6 inches.

Check that all three pieces are the same size.

Lightly sand the edges that will remain exposed.

Step 5: Cut the Pocket Bottom Panels

Prepare three bottom panels using the preliminary 11 × 2 1/2-inch dimensions.

Check the fit against the planned side-piece arrangement.

Trim the panels as necessary after the pocket geometry is finalized.

Step 6: Design the Angled Side Pieces

Draw a side profile for each magazine pocket.

The profile should provide a shallow bottom and a front panel that slopes outward slightly from the back panel.

Use a cardboard template to check the angle and projection.

Confirm that the profile retains magazines without allowing them to fall forward.

Step 7: Cut the Side Pieces

Transfer the finalized profile to the wood.

Cut six matching side pieces.

Use the first completed piece as a template for the remaining pieces.

Sand the shaped edges carefully.

Step 8: Dry-Fit the First Pocket

Arrange one front panel, one bottom panel, and two side pieces.

Check that the parts fit together correctly.

Place a magazine inside the temporary assembly to confirm the storage depth and front angle.

Make any necessary adjustments before fastening the components.

Step 9: Assemble the First Pocket

Apply wood glue to the mating surfaces.

Join the front, bottom, and side pieces using suitable small-box joinery and fasteners.

Clamp the assembly carefully.

Check that the pocket remains square where intended and that the front angle matches the design.

Step 10: Assemble the Remaining Pockets

Repeat the assembly process for the other two pockets.

Check that all three pockets have consistent dimensions and angles.

Allow the glue to cure according to the manufacturer’s instructions.

Step 11: Mark Pocket Positions

Lay the back panel flat on a protected work surface.

Position the three completed pockets on the panel.

Check the vertical spacing and alignment.

Mark the mounting locations for each pocket.

Step 12: Attach the Pockets to the Back Panel

Secure each pocket to the back panel using suitable fasteners or joinery.

Pre-drill holes where necessary to prevent splitting.

Make sure the pocket attachments can support the intended magazine load.

Check that the pockets remain level and firmly attached.

Step 13: Sand the Completed Rack

Sand all exposed surfaces and edges.

Round sharp corners slightly.

Pay particular attention to the pocket openings, where magazines will be inserted and removed.

Step 14: Apply Paint or Stain

Choose a finish that complements your room.

Apply paint, stain, or clear coating according to the manufacturer’s instructions.

Allow the finish to cure fully before installing the rack or adding magazines.

Step 15: Select the Wall-Mounting Hardware

Choose a mounting method appropriate for the rack’s weight, expected contents, and wall construction.

Fastening into suitable wall studs or other structural backing is generally preferable.

If using anchors, follow their manufacturer’s instructions and load limits for the specific wall material.

Step 16: Mark the Wall Location

Hold the rack in its intended position.

Use a level to check the alignment.

Mark the mounting locations.

Check for hidden electrical wiring, plumbing, and other services before drilling.

Step 17: Mount the Magazine Rack

Install the selected mounting hardware according to its instructions.

Attach the rack securely to the wall.

Check that the back panel is stable and that the mounting points do not loosen or shift.

Step 18: Organize Your Magazines

Place a small number of magazines into each pocket.

Check that the pockets retain the publications securely.

Distribute the weight evenly and avoid overloading the organizer.

How to Choose the Best Wood for a Magazine Rack

Pine

Pine is widely available and relatively easy to cut, making it a useful choice for beginner woodworking projects.

Poplar

Poplar can be a good option for painted furniture and organizers.

Oak

Oak provides a distinctive grain pattern and can create a traditional furniture-style appearance.

Maple

Maple offers a clean appearance and can work well with clear finishes.

Plywood

Suitable plywood provides consistent panel dimensions and can be practical for the back panel and magazine pockets.

Magazine Rack Slot and Pocket Design Tips

Pocket Width

Choose a width that accommodates the magazines you plan to store.

Allow a little extra space so magazines can be removed without catching on the side panels.

Pocket Depth

Shallow pockets can display more of a magazine cover, while deeper pockets may retain thicker publications more securely.

Front Angle

A slightly outward-sloping front can improve access.

Test the angle with actual magazines before cutting all the side pieces.

Vertical Spacing

Leave enough room between pockets to insert and remove magazines comfortably.

Weight Distribution

Spread magazines across the pockets rather than placing all the weight in one location.

Wall-Mounting Safety Considerations

A wall-mounted magazine rack must support both its own weight and the weight of the stored publications.

  • Use mounting hardware suitable for the wall construction.
  • Attach to structural backing where appropriate.
  • Follow the manufacturer’s installation instructions and load ratings.
  • Do not assume drywall alone can support the rack.
  • Check for concealed wiring and plumbing before drilling.
  • Keep the rack out of locations where it could obstruct walking areas or doorways.
  • Inspect the mounting points periodically.

Important: This example does not have a tested load rating. The allowable weight depends on the materials, pocket joints, back-panel connections, mounting hardware, and wall structure.

Magazine Rack Customization Ideas

  • Natural wood finish: Highlight the grain with a suitable clear coating.
  • Painted rack: Match the color to nearby furniture or walls.
  • Contrasting pockets: Use a different color for the pocket fronts.
  • Decorative trim: Add simple trim to the back panel.
  • Extra pockets: Extend the back panel and add storage levels.
  • Office organizer: Adapt the pocket dimensions for folders or lightweight documents.
  • Rustic style: Use a simple finish that emphasizes the wood texture.

Common Magazine Rack Building Mistakes

  • Pockets too narrow: Measure the intended magazines before cutting.
  • Incorrect front angle: Test a sample pocket before making all three.
  • Uneven spacing: Mark the pocket positions carefully.
  • Weak pocket attachments: Use suitable joinery and fasteners.
  • Rough edges: Sand the pocket openings to prevent snagging.
  • Improper mounting: Use hardware appropriate for the wall and load.
  • Overloading: Avoid storing more weight than the rack and mounting system can safely support.

Frequently Asked Questions About DIY Magazine Racks

Is a wooden magazine rack a good beginner project?

Yes. A simple magazine rack provides practice with measuring, cutting, assembly, sanding, and finishing. Angled pockets and wall mounting require additional care.

What is the best wood for a magazine rack?

Pine, poplar, oak, maple, and plywood can all be suitable choices. The best material depends on the intended appearance, budget, and construction method.

How wide should a magazine rack be?

The rack should be wide enough for the magazines or catalogs you intend to store. This example uses 12-inch-wide pocket fronts and a 14-inch-wide back panel.

Can I build a magazine rack from 1×12 lumber?

Yes. Nominal 1×12 lumber can be used in magazine rack construction. The original Pinterest-inspired design references this material, while the separate example in this guide uses panel components.

How do I attach a magazine rack to the wall?

Use mounting hardware appropriate for the rack, expected contents, and wall structure. Follow the hardware manufacturer’s instructions and secure the rack to suitable structural backing where possible.

Can I add more storage pockets?

Yes. A taller back panel can accommodate additional pockets, provided the structure and wall mounting are designed for the increased load.

Can I use the rack for mail?

Yes. The pockets can be adapted for envelopes, brochures, or lightweight paperwork. Smaller pocket dimensions may be more convenient for mail.

Can I make a freestanding magazine rack instead?

Yes. A freestanding rack is another option, but it requires a separate base and stability design rather than the wall-mounted construction described here.

Conclusion

A wooden magazine rack is a useful woodworking project that combines compact storage with a decorative appearance.

The example in this guide provides a starting design for a 14-inch-wide wall-mounted organizer with three angled magazine pockets.

Accurate measurements, carefully fitted pocket components, smooth edges, and suitable wall-mounting hardware are important for a successful result.

The Pinterest blueprint above offers additional inspiration for creating a magazine rack suited to your home, office, and reading materials.

DIY wall-mounted wooden magazine rack design with angled storage pockets

Affiliate Disclaimer. At 123Woodworking, we believe in transparency and honesty on the internet. We want to disclose that this site includes links to certain products. We earn an affiliate commission on any purchases you make. With this disclaimer, our blog aims to educate gardening enthusiasts about opportunities in their field. Please understand that we operate as a for-profit business.